I am your Guy WITH experience with Fusion, Discectomy, Epidurals, etc, etc..etc..
YOU are Very Lucky that someone even Mentioned the Spinal Stim to you...!
The "average" Back Sturgeon will NOT tell you a thing about it..Sad but True..
I did my homework and asked my Primary Dr to "Refer Me" to Dr Gladstone Churchill McDowell..St Judes, Columbus, Ohio.. I had to take a few preliminary tests and Interview with The Dr several times.. He put it in for a "7 to 10 Day Trial"...took him about 10 Minutes.. Over the 1st 3 days, I was just trying to find how much Stim I needed and I was Over-Stimulating way too much..!! I actually "went down" once and could not get up..until I turned the Stim off..! I learned that it does not take a whole lot of noticeable Spinal Stim, to BLOCK the Pain..! I have had a good SOLID, Reliable 85% Reduction in Lower back and Rt Hip/Thigh pain/numbness since it was installed... I have 10 different Programs I can choose from and adjust them a Great deal, each.. And they can put more in if I think I need them..! I had quit Western Square Dancing 10 Years prior to this and am now a Steady Strong _ level Square Dancer..! Before, if I did try, I had to have someone ready to "Step in" as my Rt Foot and Leg would go numb... What I have found now is that I do need to Turn the unit OFF, if I am going to Square Dance, or I get a weakness in my legs, during the steady movement..BUT..I may NOT need to turn it back ON for 3 or MORE Days..as the Stim seems to have a Strong Residual effect..!!! Do I "Like it"...????? My Neuro-Surgeon was ready to schedule ANOTHER Fusion (You don't need those rods now..we can just Slide them UP"...was her reply..!! I am SO Glad I looked into this... I only need to lay on a small pad for 1 Hour, Once every week or two, to charge it..Totally NO Connections..!! ONE MORE Thing... There are 2 Different ways this can be Implanted..the "Open" and the "Closed".. You want the "Closed" Implant..Far less traumatic, with far less chance of Infection.. My neighbor had an "Open Implant" and it did NOT go well.. Where are you Located..?? IF you are anywhere near OHIO, I would advise you to see Dr Mcdowell.. He has many options to control "Pain"..that is "What he Does"..and it would include morphine pumps and more..for severely bad Cancer patients, etc.. Hope this is what you were looking for...It WORKS for ME..!!! Ron..
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Harvestin Hay: The Early Years (Part 2) - by Pat Browning. The summer of 1950 was the start of a new era in farming for our family. I was thirteen, and Kathy (my oldest sister) was seven. At this age, I believed tractor farming was the only way, hot stuff -- and given a chance I probably would have used the tractor, Dad's first, a 1936 Model "A" John Deere, to go bring in the cows! And I think Dad was ready for some automation too. And so it was that we acquired a good, used J. I. Case, wire tie hay baler. In addition to a person to drive th
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
