Farmall & IHC Tractors Discussion Board |
Re: Re: Re: Bellering H
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Allan in NE on June 02, 2004 at 18:12:06 from (148.63.132.164):
In Reply to: Re: Re: Bellering H posted by riverbend on June 02, 2004 at 15:42:54:
Greg, I'll try. This makes about the millionth time I've wished that I had taken pictures of all that farm equipment. Now, it is only in my minds eye as most of this old stuff that we all used to use has been cut up for scrap by many of these salvage yards and just is no more. Think of a regular 6 row cultivator on the H. Instead of cultivator shanks being the size you would imagine, they were huge "C" shaped things coming down from the cultivator frame (one for each row) with a 4 foot long, 6 inch wide knife attached (flat side down)to it's foot. The knife was attached in such a way and was angled so that the total cut for that one knife amounted to about 12" as it slide thru the ground snapping the beans off along the row. The problem with beans are the vines. The crop has to be handled when the dew is down so that the vines are "tough" and the pods will not shell out. So, also at each "shank" were long 3/4" dividing rods to guide each cut row around the tires and to it's "windrow". Out in front of the whole she-bang were larger dividers, one for each tire. The rear of the cultivator was not attached. Later on we started using a rod weeder at the rear to make sure we got all the beans pulled. Newer models nowadays just use a set of dividers out in front of the tractor, lift the beans with a rod weeder behind the tractor and dump 'em into an attached windower behind that. This is a picture of an older front mounted model covering 8 30" rows. If you can imagine 6 of those rows in 22" spacing, and the whole thing squeezed up under the belly of an H. That was the first bean cutters. I tried, :>) Allan
Follow Ups:
Home
| Forums
Today's Featured Article -
The Rescue of a Fordson F - by Anthony West. Introduction I live in the UK and have for many years restored Fordson tractors (in the main model N's). I have also restored and shown model F's, E 27N's, Field Marshall Series 2, David Brown Cropmasters and the old rey Fergeson T 20. At one time I had seven restored examples which were shown and used in ploughing matches. As most restorers, I have a number of war stories I can relate on a range of topics that may help other like minded and interested people. Perhaps my first p
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|