Farmall & IHC Tractors Discussion Board |
Re: Re: crankshaft farmall super c
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Stan(VA). on August 16, 2003 at 21:28:09 from (208.59.156.129):
In Reply to: Re: crankshaft farmall super c posted by Vyron Mayle on August 16, 2003 at 12:08:41:
OK, #46402DB is A/B crankshaft note: they list a change around ser #146040 but don't get specific, maybe DA/DB suffix? #356308R1 is standard C/Super C/200/230 crankshaft #251587R92 is replacement crankshaft for A/B/C/SC note: this gets hairy the later you go because parts books list the crank 'assy' w/ bearings and changes the number for a factory turned crank (.030) All these reference the same connecting rod #30926DF #368711R1 is 240 crankshaft My experience: I pulled a 356308 crankshaft out of a B engine block (obviously a transplant, also had a later cyl head on it) and put it in a Super C block (#354898) and am still using that motor today. So the later cranks will go in the earlier motors, and I assume the other way around but can't say definitively based on experience. Hugh, The parts books show so many ser # breaks on the Super A's I got a headache ;) ;) But if I surmise correctly reading between the lines..., they went to the new block with larger sleeve openings at ser #310300 (but apparently w/ very thick sleeves to maintain 3" bore), then came out with the SA-1 at #356001 with the thinner sleeves for 3 1/8" bore, taller radiator and water pump... Vyron, My extra crank I am 90% sure is the #356308, will have to check tomorrow. It came from a running motor but will need to be cleaned and turned. I would sell it for $50 as is, or through the shop w/o bearings (est $110). I'm taking a 240 crank in this week so could get it done easily. Email me direct if interested, or if I can help further. I am in VA. Stan(VA).
Follow Ups:
Home
| Forums
Today's Featured Article -
Uncle Cecil's Super A Lives Again - by Mike Purcell. A week or so out of most of my childhood summers was often spent with my Uncle Cecil and Aunt Sissie in the small East Texas town of Maydelle on their 80 acre farm. Some of my fondest memories of these visits are those of learning to drive a tractor at the helm of Uncle Cecil’s 1948 Farmall Super A. Uncle Cecil was the second owner of this wonderful little tractor, but it was almost as though he had adopted an infant. The original owner was a man from Minnesota who bought her from a local dea
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|