Farmall & IHC Tractors Discussion Board |
P.T.O. / Belt pulley attachment question for an A
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Steve T on May 17, 2003 at 07:28:09 from (216.187.162.164):
Iv finly worked my way back to the P.T.O. / belt pulley attachement on my "A" in this little restoration project and and am stuck on a problem. This is a 1940 model and has a different P.T.O. setup then the latter A's. How is the gear oil supposed to stay in the belt pulley box? The bearing I took out (the one between the pulley box and the P.T.O. box) is not sealed on one side. It looks to me that when opperated, that the pulley box oil can run through the bearing and into the transmission, and possibly starve the Belt pulley gears for oil. I bet those 2 bevel gears can really sling the oil when running. The original owners manual doesnt have a section on the P.T.O. as it was an option, and the I&T manual is kind of vauge. The IH bearing # crossed over to is a 206-J which is an open bearing, no seal. The latter style box that I have also doesent have a seal on it, but has a hole through the case between the transmission and belt pulley box, and no slinger. The `40 style setup has a big wafered oil slinger disk bolted to the front of the P.T.O. shaft to help keep the transmission bearings oiled when the tractor is stationary and using the belt pulley.The latter style transmission doesnt have this slinger, but instead has a "oil roller gear" mounted on first gear on the lower gear cluster. (I updated the transmission to include this gear.) Does the waffered slinger help pass oil back through the bearing into the belt pulley box? Or do I need a special sealed bearing? If any one has a parts breakdown for an early "A" P.T.O./ belt pulley setup, could you please post the belt pulley box bearing numbers for me? Or if you have had one of these early box's apart for a rebuild, what was in your box? Thanks for your time. Steve T in MT
Follow Ups:
Home
| Forums
Today's Featured Article -
The Rescue of a Fordson F - by Anthony West. Introduction I live in the UK and have for many years restored Fordson tractors (in the main model N's). I have also restored and shown model F's, E 27N's, Field Marshall Series 2, David Brown Cropmasters and the old rey Fergeson T 20. At one time I had seven restored examples which were shown and used in ploughing matches. As most restorers, I have a number of war stories I can relate on a range of topics that may help other like minded and interested people. Perhaps my first p
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|