Farmall & IHC Tractors Discussion Board |
finaly got my super c running but... LONG
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by dan on May 05, 2002 at 07:14:06 from (68.83.34.37):
yesterday I finnished rebuilding my super c engine and fired her up. everything went perfectly except for the head gasket was leaking out the sides a little. it was a felpro gasket so I know, you dont have to say it. I'll get a new one at the case dealer this week and do it right. this morning I started it up and it started ticking. guess how mad I was to find a bent push rod. the machinist at a local big named parts store that I wont't name is sure lucky they are closed today. I took the head to him last monday. I had already removed the guides and resurfaced the valves and cleaned the head at work. I wanted him to install new guides and cut the valve seats. that was all I said to do and I was very specific! well he took it upon himself to replace the springs also ( I had already baught new ones at the dealer) he put the wrong kind on it for one thing. the exhaust valves all have rotators with special springs. he installed what their book said was right and beleive me if I had tried to start the engine the way he had set it up it would have been a very bad day. he also didnt intall the guides at the height I specified. .750 inch I told him and I also wrote it down. he installed them at 1.125. the valves could only be pushed down 1/16 of an inch by hand like that and there was no room for the valve safety clips. also umbrella seals were on it and I told him it didnt come with seals and if he did the job right it wouldnt need seals. well I was up most of the night fixing all of this "machinists" mistakes and I guess the moral to this story is know your mechanic or machinist and never never never trust someone else to do work that you could have done yourself! I work as a mechanic at a case and kubota dealer and was an engine machinist for 15 years. I just didnt have the time so i took it to someone else.
Follow Ups:
Home
| Forums
Today's Featured Article -
The Rescue of a Fordson F - by Anthony West. Introduction I live in the UK and have for many years restored Fordson tractors (in the main model N's). I have also restored and shown model F's, E 27N's, Field Marshall Series 2, David Brown Cropmasters and the old rey Fergeson T 20. At one time I had seven restored examples which were shown and used in ploughing matches. As most restorers, I have a number of war stories I can relate on a range of topics that may help other like minded and interested people. Perhaps my first p
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|