|
Tune-Up Specifications - John Deere |
This data has been gathered from old out-of-print material. While
we make every effort to be accurate, the information shown is to
be used for general reference only. It is always best to have
the original service or operator's manual for your tractor before
attempting any tuneup.
There is a legend at the bottom of the page describing some of the terms used here.
|
Model
|
Point Gap
|
Spark Plug Gap
|
Timing Mark On
|
Spark Occurs
|
Firing Order
|
Int. Valve Clearance
|
Exh. Valve Clearance
|
Comments
|
|
M,MT |
.020 |
.025 |
FLY |
TDC |
1-2 |
.012C |
.012C |
For magneto set point gap to .015 |
|
L,LA |
.020 |
.025 |
FLY |
TDC |
1-2 |
.006H |
.008H |
For magneto set point gap to .015 |
|
H (All Fuel) |
.015 |
.030 |
FLY |
|
1-2 |
.015H |
.015H |
Spark occurs when dot or "LH-Impluse" aligns with index on cover or case. |
|
G (All Fuel) |
.021 |
.030 |
FLY |
|
1-2 |
.020H |
.020H |
For magneto set point gap to .015 - Spark occurs when dot or "LH-Impulse" aligns with index on cover or case. |
|
D (All Fuel) |
.015 |
.030 |
FLY |
|
1-2 |
.030H |
.030H |
Spark occurs when dot or "LH-Impluse" aligns with index on cover or case. |
|
B (All Fuel & Gas) |
.015 |
.030 |
FLY |
|
1-2 |
.020H |
.020H |
Spark occurs when dot or "LH-Impluse" aligns with index on cover or case. |
|
A (All Fuel & Gas) |
.021 |
.030 |
FLY |
|
1-2 |
.020H |
.020H |
For magneto set point gap to .015 - Spark occurs when dot or "LH-Impulse" aligns with index on cover or case. |
|
80 Cranking Engine |
.020 |
.025 |
FLY |
30 deg. BTDC |
1-2-3-4 |
|
|
|
|
70 Cranking Engine |
.020 |
.025 |
FLY |
30 deg. BTDC |
1-2-3-4 |
.020H |
.020H |
|
|
70 (LP), 60 (LP) |
.022 |
.030 |
FLY |
5 deg ATDC |
1-2 |
.020H |
.020H |
|
|
70 (Gas) |
.022 |
.030 |
FLY |
10 deg. ATDC |
1-2 |
.020H |
.020H |
|
|
70 (All Fuel), 60 (All Fuel) |
.022 |
.030 |
FLY |
TDC |
1-2 |
.020H |
.020H |
|
|
50 & 60 (LP & Gas) |
.022 |
.030 |
FLY |
5 deg ATDC |
1-2 |
.020H |
.020H |
|
|
50 (All Fuel) |
.022 |
.030 |
FLY |
TDC |
1-2 |
.020H |
.020H |
For point gap, for LP set TDC. |
|
40 (All Fuel) |
.022 |
.025 |
FLY |
3 deg ATDC |
1-2 |
.012C |
.012C |
For point gap, for LP set TDC. |
| Legend |
|---|
- TDC - Top Dead Center
- FP - Crankshaft Fan Drive Pulley
- Exh - Exhaust
- Int - Intake
- ATDC - After Top Dead Center
- BTDC - Before Top Dead Center
|
|
Data collected from an old Niehoff tune-up chart.
|
Home
| Forums
Today's Featured Article -
Listening to Your Tractor - by Curtis Von Fange. Years ago there was a TV show about a talking car. Unless you are from another planet, physically or otherwise, I don’t think our internal combustion buddies will talk and tell us their problems. But, on the other hand, there is a secret language that our mechanical companions readily do speak. It is an interesting form of communication that involves all the senses of the listener. In this series we are going to investigate and learn the basic rudimentary skills of understanding this lingo.
... [Read Article]
Latest Ad:
2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
