(800) 853-2651
SHOP NOW

set a new record today

E

ericlb

Well-known Member
brush hogged today, took me 4 hours to do 10 feet! thats when the orc decided to blow apart, when i went to town i got the usual blank look, parts kids had no idea what a tractor over running clutch even is, lucky i had an old adapter, so i got some done this evening, but i still have a 140 mile trip to get the replacement over running clutch, in its defense that one has seen 5 years of heavy use so i got my use out of it , and it didnt even bend the driveshaft on the brush hog
 
Or, how about greasing it EVERY time you use it? My original over-running clutch is over 40 years old and is now on its second tractor and second brush hog. Fifty cent a tube lube is cheap over the cost of a new ORC.
 
That where I brought mine.
The problem was I put it on and hooked up the rotary cutter. Afterwards I lifted the cutter up and didn't realize until it was too late the pto shaft was now too long. I bent the base on the cutter where the gear box is bolted on and the blades were now hitting the deck underneath. I was glad it was my old 30 year old House backup cutter that I was thinking of getting rid of anyway. I finally got around to working on it yesterday and decided to shim the gear box to level it out again. I haven't tried it yet. I hope it works.
 
i do that, yours is probably much better quality than what is out there today, also i do custom cutting, in the summer i run mine 6 to 8 hours a day 7 days a week, sometimes more, my place gets its pastures done at night, right now im looking forward to the end of the season, im burned out on this stuff
 
You must log in or register to reply here.

Similar threads

V
new owner of a 620, will try to update this as we go.
2 3 4
Replies
61
Views
4K
valiant8086
V
P
1955 Farmall 100 Engine Overhaul
2
Replies
38
Views
3K
BarnyardEngineering
BarnyardEngineering
B
2 ton+ grass with a haybine
2
Replies
22
Views
1K
730virgil
7
A
Getting a 'new' tractor - give me advice to not screw up
Replies
7
Views
1K
Husker 50 8n
H
olgentdc
B-i-L Joel passed away His Eulogy 10-22--56/// 11-8--
Replies
9
Views
1K
olgentdc
olgentdc
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top