TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Discussion Forum

Easy question

Welcome Guest, Log in or Register

Author

Dan S (NY)

03-03-2002 13:34:53

Report to Moderator

Ok, heres an easy one. I am replacing the cobbed up muffler and pipe held up by bits of wire that came with my TO20. I have the new exhaust but where where the original muffler hanger(s) attached and what did they look like? I could rig somethng easily enough but would like to put it back the way it should be if possible.

Thanks! Dan

[Log in to Reply] [No Email]

Bill Mc

03-03-2002 16:57:03

Report to Moderator

Re: Easy question in reply to Dan S (NY), 03-03-2002 13:34:53

Hey Dan
This is the clap on my TO20,I think it is original. I almost didn't post the picture(under belly needs paint:0) Good Luck

Bill Mc

[Log in to Reply] [No Email]

Bowser

03-04-2002 10:22:30

Report to Moderator

Re: Re: Easy question in reply to Bill Mc, 03-03-2002 16:57:03

Bill Mc,I was incorrect when I stated that the rear bracket bolted to the the hydraulic oil dip stick cover bolt,the right hand footboard bolts there and not the the rear bracket as I said.Your picture shows the correct mounting for the rear bracket at the axle housing bolt.Old age is beginning to affect my memory.
Bowser

[Log in to Reply] [No Email]

Dan S (NY)

03-04-2002 14:28:02

Report to Moderator

Re: Re: Re: Easy question in reply to Bowser, 03-04-2002 10:22:30

Thanks.. Bill Mc, the underside of mine needs paint too. Going to wait till warmer weather arrives on a more consistant basis before painting anything. Was 60 yeaterday and now its 17 degrees.
Dan

[Log in to Reply] [No Email]

Bowser(VA)

03-03-2002 14:37:19

Report to Moderator

Re: Easy question in reply to Dan S (NY), 03-03-2002 13:34:53

The the origional TO-20 exhaust system had (1)clamp that went around the muffler and attached to the footboard thru a countersunk hole in the footboard and(1)that clamped around the exhaust pipe and bolted to a bolt in the side cover where
the hydraulic oil dip stick is.They can be made by using 1/8" X 1" cold rolled steel flat bar.Most
any machine shop should have the cold rolled steel

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Copyright © 1997-2023 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy