Tractor Talk Discussion Board |
RESTORING TIE-ROD ENDS AND SUCH
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Ken McWilliams on November 02, 2000 at 19:12:59 from (152.163.197.72):
I have a Massey Ferguson 50A which is the base tractor for a backhoe. It's closest derivation is a MF-165. I've just finished rebuilding the Perkins diesel AD4-203 with a kit from Tisco. The whole kit was $525. Then I rebuilt the shuttle replacing the detents and a collar shifter which cost and outrageous $400 from MF. Now I'm rebuilding the front axle. The bushings and thrust bearings for the spindle shafts are shot. One of the thrust bearings was completely disintegrated. I can get the 4 bushings from Motion Industries for about $5 each. MF wants $49.50 each(10 times as much). I'm going to get the closest match to the thrust bearings to fit a 1.75 inch shaft. Motion wants about $20 each, and MF wants around $60. The tie-rods are massive along with everything else on this tractor. The price on them from MF I know is going to be very expensive. Therefore, I'm going to try and restore them. The sockets are completely worn out. The balls are barely retained in the socket of the tie-rod end. At first, I was thinking of heating them cherry red and peening over the open end to close the gap. Then I thought about my new truck that has ball joints and tie-rod ends that have injection molded plastic in the joints for wear. The new vehicles have greaseless joints. Instead of heating and peening, how about heating the joint and melting some thermoplastic Delrin or Nylon into the joint? An alternative would be to use some epoxy. I have some mold release in the garage. Apply mold release to the ball and socket and then pour some Devcon or JB Weld. If it doesn't work, I can always burn it out and try something else. I may be able to find some flaked teflon to mix into the epoxy when I pour it to give some lubricity quality when in use. Anyone have any ideas? Ken McWilliams Dayton, OH
Follow Ups:
Home
| Forums
Today's Featured Article -
An Old-Time Tractor Demonstration - by Kim Pratt. Sam was born in rural Kansas in 1926. His dad was a hard-working farmer and the children worked hard everyday to help ends meet. In the rural area he grew up in, the highlight of the week was Saturday when many people took a break from their work to go to town. It was on one such Saturday in the early 1940's when Sam was 16 years old that he ended up in Dennison, Kansas to watch a demonstration of a new tractor being put on by a local dealer. It was an Allis-Chalmers tractor dealership,
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|