Posted by Lanse on October 09, 2015 at 11:23:46 from (99.190.213.134):
Hey yall!
Well, I wanted to thank you all for the replies to my last thread about my international 2444. I screwed with it for an hour or so today and found that the linkages, as I had them were wrong, and also, the way they were when I bought the tractor was wrong!
After some thought and tinkering, I had the linkage setup so that the throttle plate opens the right way, the tractor starts and doesnt surge, and just plain runs right.
Also, with the carb cleaning I gave it when it was apart, and the new fitting and fuel line, the tractor runs smoother than it ever has for me, plus it starts easier and doesn't leak a single drop of fuel!
While I was at it, I discovered that the way the previous owner configured the linkage, prevented the linkage from going all the way into its idle position. Once I fixed that, the idle RPM's dropped from ~1300 to ~800 and its much more pleasant to work around now.
I'm pretty thrilled! Also, thank you so much to everyone here who taught me what little I know about turning wrenches in years gone by, the lessons I learned here will always help me and it means a lot to me...
Oh, and one other thing. In the spirit of this thing always needing something done to it, I figured I might as well work on this brake linkage, the one in the picture.
When you hit the brakes, this lever slides forward and keeps them from disengaging, it acts like you set the parking brake when you didnt want to. Its a little irritating, because you have to hold the lever back against the tension of the spring attached to it, then release the brakes, every single time you use them. How should I work this, so that it doesn't happen anymore?
I cant imagine that it came this way from the factory, but I've also looked over it and cant find anything that appears to be broken or missing. Thanks in advance!
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - An Old-Time Tractor Demonstration - by Kim Pratt. Sam was born in rural Kansas in 1926. His dad was a hard-working farmer and the children worked hard everyday to help ends meet. In the rural area he grew up in, the highlight of the week was Saturday when many people took a break from their work to go to town. It was on one such Saturday in the early 1940's when Sam was 16 years old that he ended up in Dennison, Kansas to watch a demonstration of a new tractor being put on by a local dealer. It was an Allis-Chalmers tractor dealership,
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
