Posted by ScottyHOMEy on October 24, 2009 at 22:44:39 from (70.105.238.87):
In Reply to: Belt pulley thoughts posted by Mike CA on October 24, 2009 at 22:09:56:
The first obvious question, Mike, is what kind of shape is yours in?
I'll admit that when I started working on tractors instead of working on and around them was to learn that the core of the pulley on your tractor is paper. I'd seen the one on Grandpa's H and always thought it was a turned piece of wood. It was a shedded tractor, never left for more than a few days out in the weather but the shed idn't have doors either. By the time I came along, it was probably fifteen years since the tractor had been belted up to anything, but it still had a glaze and sheen to the surface of it. I know nothing of what goes into them, but expect that it's a mix of hard, tacky waxes or resins that will shine but be tacky as they warm up. Some of that may have been a residue from a belt dressing that worked its way into the fiber.
So the next question is whether you have some evidence of that and then what physical shape your pulley has. You've seen the metal pulleys. If your paper pulley still has something of the ridge/dome in the middle, you may not have to do anything. That's all you need to get a wide belt to ride properly on it.
If it's crumbling or no lnoger has a dome or, worse yet, is recessed inside the ends, then it would be time to see about having it redone or trading in the core, however those folks do things.
If it still has that dome/ridge shape, I'd suggest you develop some contacts with some of the guys at the tractor shows and see if you can't arrange to get to a show and belt up to something, a buzz saw, a hay press, or (my dream) a thresher . . . Bring your own can of belt dressing, but let the fellow who owns the belt apply it. If yours is at all dry, it will soak up any excess but, more importantly, with the heat of working, will seal up and glaze over to protect it from deteriorating.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The 8N and the Fox - by Zane Sherman. Dec. 13 1998, Renfroe, Alabama. Last niht I dreamed about the day that I plowed the field of about 10 acres over on what Jimmy and Dandy called the Ledbetter field. I was driving the 1948 8N Ford tractor that Jimmy bought in 48 new This was prebably in about 1951 and maybe even befor the house was built. This would have made me to be about16 years old and I drove the tractor for nothing and would have paid to drive it if I had had any money which I didn't, but neit
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.